Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected performance. Fortunately, resetting your Holosun is a straightforward process that can be achieved in just a few actions.

• First ensuring your red dot sight is activated.
• Identify the small button for reset on the rear of the unit.
• Utilize a paperclip to press and hold the reset lever for approximately three moments.
• Release the reset button and your Holosun EPS Carry Red Dot sight will reboot.
• The red dot sight should now be returned to its factory settings.

Restore Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to default configuration is a breeze. First, locate the tiny button on the bottom more info of your optic. Then, keep pressed it for around twelve seconds until you see a brief flash. Your Holosun EPS Carry is now reset to its factory settings, ready for accurate shooting.

Bring Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Press and hold the power button for approximately 7 seconds.
• An indicator will flash, indicating that the reset is successfuly initiated.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and test your sight's functionality. If you encounter any further problems, don't hesitate to contactsupport team.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• Initially, Activate your Holosun EPS Carry by pressing the power button.
• Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
• While continue holding these buttons, press the power button once.
• A message will show a confirmation prompt indicating that the reset process is initiated.
• Permit the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Restore your Holosun EPS Carry with a Factory Default Settings

If your Holosun EPS Carry is acting up, a factory reset might be the answer. This will set back your sight to its initial settings, clearing any personalized configurations you've made. To perform this reset, observe these straightforward steps:

• First, find the reset button on your EPS Carry.
• Next, use a fine object, like a toothpick, to depress the reset lever.
• During keep the reset button pressed, turn your EPS Carry.
• You'll flash a message indicating that the reset is successful.

After the reset is finished, your EPS Carry will be returned to its factory settings.

Report this wiki page